| Power Stage Module (PS Module) |
Description |
| PS-FBD 2/1 |
- 2-channel full-bridge driver module
- Requires 1 slot in a RapidPro unit
- Each driver 5 A continuous, 7 A peak (depending on the Power Unit the module is mounted in)
- Maximum supply voltage: 40 V continuous, 45 V peak (0.5 sec)
- Usable as: full-bridge, half-bridge, low-side or high-side driver
- Software-adjustable current limitation and switch-off time
- High-side rise time: 1.8 μs typ., 3.5 μs max., high-side fall time: 0.2 μs typ., 0.8 μs max., low-side rise time: 6.5 μs typ., 11 μs max., low-side fall time: 4.3 μs typ., 6.5 μs max.
- Detailed load failure diagnosis
- Current measurement with software-adjustable filters (2nd-order) on both channels
- Overload protection, overtemperature protection, short-circuit protection to ground, UBAT and across the load
- Integrated on carrier board: load dump protection up to +100 V, reverse voltage protection up to -100 V
|
| PS-LSD 6/1 |
- 6-channel low-side driver module
- Requires 1 slot in a RapidPro unit
- 4 output channels with up to 5 A (hardware-configurable)
- 2 output channels with up to 1 A
- Max. supply voltage: 37 V continuous
- Clamping voltage: 45 V or 70 V (depending on hardware configuration)
- Switching time: <10 µs
- Detailed load failure diagnosis
- Current measurement with hardware-adjustable low-pass filter (1st-order) on channel 1 and 2
- Overload protection, overtemperature protection, short-circuit protection to ground, active output clamping
- Integrated on carrier board: load dump protection up to +100 V (only valid for internal voltage supply of the module), reverse voltage protection up to -100 V
|
| PS-HSD 6/1 |
- 6-channel high-side driver module
- Requires 1 slot in a RapidPro unit
- 4 output channels with up to 5 A, clamping voltage 48 V
- 2 output channels with up to 1 A, clamping voltage 63 V
- Max. supply voltage: 36 V continuous, 40 V peak
- Switching time: <30 µs
- Load failure diagnosis
- Current measurement with hardware-adjustable low-pass filter (1st-order) on channel 1 and 2
- Overload protection, overtemperature protection, short-circuit protection to ground, VBAT and across the load, active output clamping
- Integrated on carrier board: load dump protection up to +100 V (only valid for internal voltage supply of the module), reverse voltage protection up to -100 V
|
| PS-HCFBD 1/1 |
- 1-channel high-current full bridge driver module
- Requires 3 slots in a RapidPro unit
- Up to 60 A DC peak current (1 s), 42 A rms continuous (Tambient= 25 °C, filter frequency 1 kHz, corresponding duty cycle)
- Up to 60 A DC peak current (1 s), 29 A rms continuous (depends on ambient temperature)
- Max. supply voltage: <20 V continuous
- Current measurement with hardware-adjustable low-pass filter (1st-order)
- Internal free-wheeling diodes
- Protection against: short circuit, overtemperature, and overvoltage
- Load failure diagnostics
|
| PS-HCHBD 2/1 |
- 2-channel, high-current, half-bridge driver module
- Requires 3 slots in a RapidPro unit
- Each channel up to 30 A peak current (1 s), 25 A rms continuous (depending on ambient temperature)
- Parallel mode possible (30 A DC peak per channel, 19 A rms continuous per channel)
- Usable as half-bridge or low-side or high-side driver output
- Max. supply voltage: <20 V continuous
- Current measurement with hardware-adjustable low-pass filter (1st-order) for each channel
- Internal free-wheeling diodes
- Protection against short circuit, overtemperature, and overvoltage
- Load failure diagnostics
|
| PS-DINJ 2/11) |
- 2-channel direct-injection driver module
- Requires 2 slots in a RapidPro unit
- Single or double injector operation mode (two injectors of the same bank cannot be driven at the same time)
- Booster voltage U max: 100 V1)
- I max: 30 A peak, 15 A continuous
- Control of start injection
- Software-adjustable booster voltage
- Software-adjustable injection duration (peak and hold times)
- Software-adjustable peak current (upper and lower values), subpulse A and B available for Use Scenario B
- Software-adjustable hold current (upper and lower values)
- Detailed load failure diagnosis
|
| PS-HCFBD 1/2 |
- 1-channel high-current full-bridge driver module for 12 V and 24 V applications
- Requires 3 slots in a RapidPro unit
- Suitable for Use Scenarios A and B
- Support of DC motors and stepper motors
- Up to 60 A DC peak current (1 s), 42 A rms continuous (depends on ambient temperature)
- Max. supply voltage: 30 V
- Current measurement with software-configurable low-pass filter (1st order/2nd order)
- Protection against: short circuit, overtemperature, and overvoltage
|
| PS-HCHBD 2/2 |
- 2-channel, high-current, half-bridge driver module for 12 V and 24 V applications
- Requires 3 slots in a RapidPro unit
- Suitable for Use Scenarios A and B
- Each channel up to 60A peak current (1 s), 42 A rms continuous per channel (depends on ambient temperature, electric drive mode)
- Electrical drive mode: Control of three-phase electrical motors (BLDC motors and synchronous motors). Requires two PS-HCHBD 2/2 modules in the same Power Unit and includes a brake chopper for conversion of breaking energy into heat
- General purpose mode for controlling high current actuators (e.g. valves, resistive loads) (up to 30 A peak current. 19 A rms current)
- Each channel up to 30 A peak current per channel (1 s), 19 A rms continuous per channel (depends on ambient temperature)
- Output stages in the general purpose mode configurable as half-bridge, low-side or high-side driver
- Max. supply voltage: 30 V
- Current measurement with software-configurable low-pass filter (1st order/2nd order)
- Protection against: short circuit, overtemperature, and overvoltage
- Optional: RP-HC-CAB1 cable for connecting external loads such as three-phase electric motors
|
