DS6651 Multi-I/O Module

SCALEXIO FPGA I/O expansion for developing and testing highly dynamic control applications

The DS6651 provides high-performance I/O channels as a modular expansion of SCALEXIO FPGA base boards. Its channel set is ideally suited for highly dynamic control applications as well as for the high-fidelity simulation of electric drives and power electronics components.

  • Tailored channel set for controlling and simulating electric drives and power electronics
  • Scalable solution – Each FPGA base board can be extended by up to 5 modules
  • Onboard sensor supply

The DS6651 offers high-performance I/O interfaces for FPGA-based applications that require fast and high-resolution signal processing, such as:

  • Electric drive applications
  • Power electronics applications
  • Hybrid vehicle applications
  • Energy technology applications
  • Protocol development

In addition to custom programmable FPGA solutions, dSPACE offers an easy-to-use tool chain for model-based FPGA development in Simulink.

Key Benefits

The DS6651 Multi-I/O Module provides flexible interfaces for different position sensors, voltage measurement and generation as well as multipurpose digital I/O. Its channel set is ideally suited for highly dynamic control applications as well as for the high-fidelity simulation of electric drives and power electronics components.

The DS2655 FPGA Base Board has been designed for applications that require very fast, high-resolution signal processing, for example:

  • Hybrid vehicle applications
  • Electric drive applications
  • Processor-based electric drive simulation
  • Power hardware-in-the-loop applications
  • FPGA-based electric drive simulation
  • Energy technology applications
  • Power electronics simulation
  • Electric motor control development
  • Protocol development

Each dSPACE FPGA board can be coupled with up to five DS6651 modules to adapt the system to almost any use case. The modeling environment, extensive libraries for interfacing position sensors, and high-precision simulation of engines and power electronics components support the user and make getting started easy.

Parameter Specification
General
  • 6 A/D channels, 6 D/A channels, 16 digital I/O channels
  • 1x 50-pin Sub-D connector
  • ±60 V overvoltage protection
Analog input
  • 6 channels
  • Input voltage ranges selectable for each channel: +/- 1 V, +/- 5 V, +/- 10 V or 60 V
  • ADC resolution: 16 bits
  • Sampling rate: 5 MS/s
  • Selectable load resistor: 220 Ω (for channels 5 and 6 only)
Analog output
  • 6 channels
  • Output voltage range: +/- 10 V
  • DAC resolution: 16 bits
  • Update rate: 10 MS/s
  • Selectable transformer (for channels 5 and 6 only)
Digital I/O
  • 16 ground-based digital I/O channels
    • Channels can be configured in pairs to full differential pairs
  • Time resolution: 8 ns
Digital I/O input (ground-based mode)
  • Maximum input voltage range: 0 ... 30 V
  • Threshold voltage: 0 ... 12 V
  • Input frequency: max. 25 MHz
Digital I/O output (ground-based mode)
  • Voltage range:
    • 3.3 V TTL/CMOS
    • 5 V TTL
  • Output modes:
    • High-side switch (+3.3 V or +5 V)
    • Low-side switch (GND)
    • Push/pull
  • Output frequency: 25 MHz (max. at 50% duty cycle)
Digital I/O RS485
  • Voltage range: RS485 levels
  • Bit rate: max. 16 Mbit/s
Sensor supply
  • 2x 5 V (max. 500 mA each)
Physical size
  • Requires 1 slot
  • 232 x 100 x 19 mm (9.2 x 3.9 x 0.7 in) without fastening bracket
Typical power consumption
  • 6 W

DS6601 FPGA Base Board High-performance FPGA board with the Xilinx® FPGA technology for advanced electromobility applications DS2655 FPGA Base Board SCALEXIO I/O board with user-programmable FPGA ConfigurationDesk Configuration and implementation software for dSPACE real-time hardware DS2655 FPGA Base Board SCALEXIO I/O board with user-programmable FPGA XSG AC Motor Control Library FPGA-based control design for MicroAutoBox, MicroLabBox, and SCALEXIO ASM Electric Components Real-time models for automotive electric system and drive simulation XSG Utils Library Ready-to-use function blocks for speeding up the implementation of FGPA models
Support Contact Information

Drive innovation forward. Always on the pulse of technology development.

Subscribe to our expert knowledge. Learn from our successful project examples. Keep up to date on simulation and validation. Subscribe to/manage dSPACE direct and aerospace & defense now.

Enable form call

At this point, an input form from Click Dimensions is integrated. This enables us to process your newsletter subscription. The form is currently hidden due to your privacy settings for our website.

External input form

By activating the input form, you consent to personal data being transmitted to Click Dimensions within the EU, in the USA, Canada or Australia. More on this in our privacy policy.