FPGA I/O Modules

For expanding the I/O channels of the dSPACE FPGA base boards

Three I/O modules are available for expanding the I/O channels of the dSPACE FPGA base boards: the DS6651 Multi-I/O Module, the DS2655M1 Multi-I/O Module, and the DS2655M2 Digital I/O Module.

  • Providing a high number of digital and analog I/O channels
  • Three I/O modules available for dSPACE's FPGA base boards
  • Add-on with five switchable transformers

Application Areas

Three I/O modules are available for expanding the I/O channels of the dSPACE FPGA base boards. They provide a high number of the digital and analog I/O channels required for applications such as electric drives:

  • The DS6651 Multi-I/O Module, which provides a tailored channel set for controlling and simulating electric drives and power electronic components.
  • The DS2655M1 Multi-I/O Module with five analog in and out channels as well as ten digital channels. The DS2655M1 can be extended by the DS5450 SC add-on module. The add-on module contains five switchable trans­formers for decoupling the five DAC channels of the DS2655M1 module from system ground.
  • The DS2655M2 Digital I/O Module with 32 digital channels.

The I/O modules can be combined as desired to meet any use case requirements.

Technical Details DS6651

Parameter Specification
General
  • 6 A/D channels, 6 D/A channels, 16 digital I/O channels
  • 1x 50-pin Sub-D connector
  • • ±60 V overvoltage protection
Analog I/O
  • Input
  • 6 channels
  • Input voltage ranges selectable for each channel:
  • +/- 1 V, +/- 5 V, +/- 10 V or 60 V
  • ADC resolution: 16 bits
  • Sampling rate: 5 MS/s
  • Selectable load resistor: 220 Ω (for channels 5 and 6 only) Output
  • 6 channels • Output voltage range: +/- 10 V
  • DAC resolution: 16 bits
  • Update rate: 10 MS/s
  • Selectable transformer (for channels 5 and 6 only)
Digital I/O
  • 16 ground-based digital I/O channels
  • Channels can be configured in pairs to full differential pairs
  • Time resolution: 8 ns

Input (ground-based mode)

  • Maximum input voltage range: 0 ... 30 V
  • Threshold voltage: 0 ... 12 V
  • Input frequency: max. 25 MHz

Output (ground-based mode)

  • Voltage range:
  • 3.3 V TTL/CMOS
  • 5 V TTL
  • Output modes:
  • High-side switch (+3.3 V or +5 V)
  • Low-side switch (GND)
  • Push/pull
  • Output frequency: 25 MHz (max. at 50% duty cycle)
Digital I/O RS485
  • Voltage range: RS485 levels
  • Bit rate: max. 16 Mbit/s
Sensor supply
  • 2x 5 V (max. 500 mA each)
Physical size
  • Requires 1 slot
  • 232 x 100 x 19 mm (9.2 x 3.9 x 0.7 in) without fastening bracket
Typical power consumption
  • 6 W

Technical Details DS2655M1

Parameter Specification
General
  • 5 A/D channels, 5 D/A channels, 10 digital I/O channels
  • 1 x 50-pin Sub-D connector
Digital I/O
  • 10 channels, usable as input or output
  Input
  • Maximum input voltage: 15 V
  • Threshold for each channel adjustable from 0 V to 10.5 V
  Output
  • Push-pull drivers
  • One output voltage can be selected for all channels: 3.3 V or 5 V
Analog I/O Input
  • 5 channels
  • Resolution 14 bit
  • Sampling rate 4 MSPS SAR
  • Input voltage range selectable for each channel: ±5 V or ±30 V
  Output
  • 5 channels
  • Resolution: 14 bit
  • Update rate: 7.8 MSPS
  • Output voltage range: ±10 V
Physical size
  • 209 x 100 x 19 mm (8.2 x 3.9 x 0.7 in)
  • Mounted on the FPGA base board, requires one additional slot for each I/O module
Voltage supply
  • 24 V
Typical power consumption
  • 9.6 W

Technical Details DS2655M2  

Parameter Specification
General
  • 32 channels, usable as input or output
  • 1 x 50-pin Sub-D connector
Digital I/O Input
  • Maximum input voltage: 15 V
  • Threshold for each channel adjustable form 1 V to 7.5 V
  Output
  • Push-pull drivers
  • One output voltage can be selected for all channels: 3.3 V or 5 V
 

UART

  • 16 channels extended with RS232/RS485 transceivers
  • RS232: max. 250 kBaud
  • RS485: max. 16 MBaud
Maximal configuration of the functions
  • 32 x digital input
  • 32 x digital output, (push/pull or push or pull)
  • 16 x digital output, (push/pull/tristate)
  • 8 x RS232 RX, (24 digital I/O or 8 x RS232 TX channels are free)
  • 8 x RS232 TX, (24 digital I/O or 8 x RS232 RX channels are free)
  • 8 x RS485 RX, (16 digital I/O channels are free)
  • 8 x RS485 TX, (16 digital I/O channels are free)
  • 8 x RS485 RX/TX, (8 digital I/O channels are free)
Physical size
  • 209 x 100 x 19 mm (8.2 x 3.9 x 0.7 in)
  • Mounted on the FPGA base board, requires one additional slot for each I/O module
Voltage supply
  • 24 V
Typical power consumption
  • 9.6 W

Technical Details DS5450

Parameter Specification
General
  • Direct connection to the front Sub-D connector of a DS2655M1
  • Application-specific configuration of the analog I/O via onboard jumpers
  • Status LEDs for operation voltage and channel configuration
Analog I/O Input
  • Optional 220 Ω resistors for each of the five ADC channels
 

Output

  • Optional decoupling transformers for each of the five DAC channels
Digital I/O
  • Digital I/O from the DS2655M1 are routed through the DS5450 board
Power supply
  • 24V

DS6601 FPGA Base Board High-performance FPGA board with the Xilinx® FPGA technology for advanced electromobility applications DS6602 FPGA Base Board High-performance FPGA board with the latest Xilinx® FPGA technology for advanced electromobility applications DS2655 FPGA Base Board SCALEXIO I/O board with user-programmable FPGA
  • SCALEXIO Product Information, PDF, English, 16194 KB
Support Contact Information

Drive innovation forward. Always on the pulse of technology development.

Subscribe to our expert knowledge. Learn from our successful project examples. Keep up to date on simulation and validation. Subscribe to/manage dSPACE direct and aerospace & defense now.

Enable form call

At this point, an input form from Click Dimensions is integrated. This enables us to process your newsletter subscription. The form is currently hidden due to your privacy settings for our website.

External input form

By activating the input form, you consent to personal data being transmitted to Click Dimensions within the EU, in the USA, Canada or Australia. More on this in our privacy policy.